Training · 7 minute read · Updated October 20, 2026
Both cuts work by the same trick: take away the tip, and the branches below stop waiting their turn. The difference is how much control you keep over what grows back.
The common belief is that topping "makes the plant bushy" by some kind of shock. The better way to see it is hormones. The growing tip makes auxin, a hormone that holds the side buds back. North Carolina State Extension puts it plainly: auxins are produced in the stem tips and promote apical dominance by suppressing the growth of lateral buds, and removing the terminal bud eliminates the source of auxin, which allows the lateral buds to grow.
So when you cut the top, you are not hurting the plant into branching. You are removing the signal that told the branches to wait. Researchers studying cannabis describe the same thing: removing the apical meristem changes the plant's hormone balance and stimulates side shoots.
Topping and FIMing both use this. They differ in where the cut lands, and that changes what grows back.
A node is the point on the stem where leaves attach. At each node there is a bud that can become a branch.
The result is predictable: one tip out, two tips in. That is why topping is the cut most training plans are built around.
FIMing is a grower technique, not a lab one. Instead of cutting through the stem below the newest growth, you pinch or snip off most of that tiny new cluster of leaves at the very top and leave a small part of it behind.
Growers report that a FIM can push more than two new tops from one cut, and that it slows the plant less than a full topping. Results vary a lot from plant to plant, and sometimes the tip simply regrows as a single top. We could not find a controlled study of FIMing in cannabis, so treat every claim about it, including how many tops you will get, as grower experience rather than measured fact.
Ask yourself one question before you try it: do you want more tops, or tops you can predict? In a tent where you plan a flat canopy, predictable usually wins.
| Topping | FIMing | |
|---|---|---|
| Where you cut | Through the main stem, just above a node | Through the newest tip cluster, leaving a little of it |
| What grows back | Two main tops from the node below | Often several tops, sometimes just one |
| How predictable | Very | Varies plant to plant |
| Research behind it | Tested in indoor and greenhouse cannabis studies | No controlled study found |
| Easiest to plan a canopy with | Yes | Harder, because you do not know the shape in advance |
| Plant height | Shorter than an untopped plant in research | Not measured in research |
Two studies are worth knowing, with one caution: both used CBD-rich plants in research greenhouse facilities, not home tents.
The honest summary: topping reliably changes the plant's shape, and in some trials it raised yield. It is not a sure yield boost on its own. What it gives you is a shape that is easier to spread under a light.
| Approach | Main tops | Notes |
|---|---|---|
| No cut | 1 main top, many smaller ones | Tallest shape, hardest to fit under a low light |
| Topped once | 2 | The simplest reliable start |
| Topped twice (each new top cut again) | 4 | Adds veg time for the second recovery |
| FIMed | Varies | Can give more, but you cannot plan on a number |
Those top counts are simple arithmetic for topping: each clean cut turns one tip into two. Low stress training then spreads them out and pulls lower branches up into the light, so the final count of good tops is usually higher than the cuts alone.
For a 2x2, 2x4 or 4x4 tent, topping once or twice is easier to manage than FIMing because you know the shape you are building. How many plants you run changes the math too: fewer plants need more tops each. See how many plants fit in a 4x4 tent, and check your local plant limit on home grow laws by state.
A cut makes the tops. Low stress training (LST) puts them where the light is. They work best together.
The full step by step, including when to flip and how much plants stretch afterward, is in training plants to fill a tent. Write down the date and node of every cut. Next grow, you will know exactly how long that strain took to bounce back, and a grow journal makes that comparison easy.
Topping cuts through the main stem just above a node, giving two new main tops. FIMing removes most of the newest tip but leaves a little of it, which can give more tops but less predictably.
Most growers wait until a photoperiod plant has 5 or 6 nodes and cut above the 4th or 5th. The plant should be healthy and growing fast before any cut.
Sometimes. In a 2022 indoor study, topped plants made significantly more flower weight than untopped ones, but in another study a single pruning did not change yield. Topping mainly gives you a shape that spreads better under the light.
Usually not. FIMing results vary from plant to plant, while topping gives a predictable two tops per cut, which makes a flat canopy easier to plan in a small space.
You can, but it is risky because an autoflower cannot get extra growing time to recover. Many growers skip both cuts on autos and use gentle bending instead.
Education only, for adults 21+ where home cultivation is legal. Updated October 20, 2026.