CannaGLAP

Blog

Propagation · 7 minute read · Updated October 15, 2026

How to clone cannabis

Short answer. Cut a healthy branch tip from a plant in veg, at least 3 inches (8 cm) long with three or more fully grown leaves, just below a node, using a clean sharp blade. Dip the cut end in rooting hormone (an IBA gel more than doubled rooting success over a willow extract in one study), push it into moist rockwool or a rooting plug, and keep it under a dome at 72 to 78 F (22 to 26 C) and 70 to 80 percent humidity with gentle light. Roots usually show in 7 to 14 days.

A cutting is a plant with no way to drink. Every leaf keeps losing water while the stem tries to grow roots from scratch. Cloning is just the art of buying it enough time.

Why most first clones fail

A fresh cutting has leaves but no roots. Leaves lose water all day through their pores, and the stem can only soak up a little through the cut. If the air is dry, the cutting wilts faster than it can root. If the air is soaking wet and still, mold moves in. Most failures come from one of those two ends.

Think about your last attempt. Did the cuttings wilt flat in the first two days? That points to dry air, too much light or too much leaf. Did the stems turn brown and mushy at the base? That points to too wet, too warm or not clean enough. The steps below are built to avoid both.

What you need

What the research says about taking cuttings

Cannabis cloning has been tested in controlled trials. Two studies are worth building your method around.

A 2018 University of Guelph study tested leaf count, cutting position, rooting hormone and leaf trimming on cannabis cuttings over 12 days:

A 2021 study on hemp cuttings found the rooting medium mattered most: rockwool rooted best, and some potting mixes barely rooted at all. Rooting hormone clearly beat no hormone, but the different IBA strengths tested did not differ much from each other.

So: use an IBA product, keep three or more leaves, do not trim the leaf tips, and choose rockwool or a proven rooting plug.

Step by step

  1. Prepare the plugs first. Soak rockwool or plugs in plain water adjusted to pH 5.8 to 6.2, then let them drain so they are moist, not dripping. Make a hole in each.
  2. Clean the blade. Wipe it with a fresh 10 percent bleach solution, then rinse. Oregon State University Extension notes that alcohol does not kill hop latent viroid, a cannabis disease that spreads on blades (more below).
  3. Choose the branch. Pick a healthy, firm shoot that is not woody, with at least three sets of leaves.
  4. Cut it long, then recut. Take a cutting at least 3 inches (8 cm) long. Then make the final cut at about a 45 degree angle just below a node, where a leaf meets the stem. Do this quickly, or under water, so air does not get drawn into the stem.
  5. Strip the bottom. Remove the lowest leaves and side shoots so about an inch of clean stem goes into the plug. Keep at least three full leaves on top, and do not trim their tips.
  6. Dip in hormone. Coat the bottom half inch to an inch of stem. Tap off the excess.
  7. Plant it. Slide the stem into the plug about an inch (2.5 cm) deep, without scraping off the hormone, and firm the plug around it.
  8. Dome and label. Put the dome on, mist the inside lightly, and label each cutting with the mother's name and the date.

The right conditions under the dome

Clone room settings
SettingTargetWhy
Air temperature72 to 78 F (22 to 26 C)Warm enough to drive root growth
Humidity70 to 80 percent RH at firstSlows water loss from leaves
VPD0.4 to 0.8 kPaGentle pull on rootless cuttings
LightLow and gentle, 18 to 24 hoursEnough to feed the cutting, not enough to wilt it
Plug moistureMoist, never soaked or dryRoots need water and air
Fresh airOpen the dome briefly each dayPrevents mold and stale air

These temperature, humidity and VPD targets match the clone stage in our VPD by stage guide. For light, low really means low: the hemp study above rooted its cuttings at a light intensity (PPFD) of only about 54 micromoles per square meter per second, a small fraction of what a flowering canopy gets. If your cuttings wilt under the light, raise it or dim it.

Watch the plug, not the calendar. Lift the tray: when it feels light, water the plugs from below or with a gentle pour. Do not let water pool in the tray.

Day by day: what to expect

A typical rooting timeline
DaysWhat you seeWhat to do
1 to 3Some droop is normalKeep humidity high, light low, mist lightly
4 to 7Leaves perk back up; lower leaves may yellowStart cracking the vents a little more each day
7 to 14White root tips appear out of the plugOpen the vents more; light can come up a little
10 to 21Roots growing out of the plug sides and bottomRemove the dome over a few days, then transplant

Both research trials above scored their cuttings at 12 days, and in the hemp study more than half showed roots by then. Some genetics are slower, and cool rooms add days, so give stubborn cuttings up to three weeks before you give up.

Transplant once several roots poke out of the plug. Move it into a small pot, not a big one. Our pot size guide explains why.

Troubleshooting

A clone copies everything, including problems

A clone is genetically the same plant as its mother. That is the whole point: same growth, same smell, same finish. It also means problems carry over.

Oregon State University Extension describes hop latent viroid as spreading through cuttings taken from infected mothers and through sap on tools. Infected plants can look healthy, and in THC cannabis it is known to reduce flower mass, trichomes and cannabinoid levels. Their sanitation guidance: clean tools between plants, and note that alcohol, hydrogen peroxide and Virkon did not inactivate it in testing, while 10 to 20 percent bleach did.

Keep your mother clean, take cuttings only from healthy plants, and track which clone came from which mother. Canna GLAP lets you start a plant record at the clone stage and follow it all the way to the jar, so if a cut performs badly you can trace it to its source.

Questions growers ask

How long do cannabis clones take to root?

Most show roots in about 7 to 14 days. Research trials scored cuttings at 12 days, when many had rooted. Cool rooms and some genetics can stretch it to about three weeks.

Do I need rooting hormone for cannabis clones?

It helps a lot. A hemp study found hormone-treated cuttings rooted far better than untreated ones, and a cannabis study found an IBA gel beat a willow extract by about 2.1 times.

Should I cut the leaf tips on my clones?

No. In a cannabis study, trimming a third off the leaf tips lowered rooting success from 71 percent to 53 percent.

Can I take clones from a flowering plant?

It is possible but much slower and less reliable. Cuttings from flowering plants have to switch back to growth first. Take cuttings from plants in veg whenever you can.

What humidity do cannabis clones need?

About 70 to 80 percent relative humidity at 72 to 78 F (22 to 26 C) at first, lowered gradually by opening the dome vents once roots start to show.

Read next

Sources

Education only, for adults 21+ where home cultivation is legal. Updated October 15, 2026.